跳至主要内容

What is Guide Pin ?

 1.Definition of guide pin

The guide pin is a guide element used in the mold in combination with the components to ensure that the mold moves and guides the mold stroke with precise positioning. They are generally cylindrical with shoulders and usually have oil grooves.
What is Guide Pin - HG
2.The material of the guide pin
The material of the guide pin is generally selected from bearing steel, hot work die steel, easy car iron, etc., and the use of bearing steel SUJ2 is larger, which greatly enhances the durability and interchangeability of the guide post in terms of guiding performance. The guide post and components constitute the outer guide post component and the inner guide post component, which have a beautiful metallic luster.

Heat treatment of guide post: HRC58-62; surface roughness of guide post: Ra0.8, Ra1.6.

3.Center hole of guide pin
The roundness of the guide pin is very demanding. The central hole is mainly used to grind the outer diameter with a cylindrical grinder, because when using a cylindrical grinder to grind the outer diameter, the center hole must be held against the center hole to rotate the guide post. Can be ground.
Guide Pins - HG
4.Classification of guide pins
Guide pins, according to different places of use, are divided into: guide pins for automobile molds, independent guide pins, guide pins for mold bases, and guide pins for unloading plates.
According to the different guiding directions, it is divided into: sliding guide pin (code SGP), rolling guide pin (code SRP).
According to the different installation methods, it is divided into: loading and unloading guide pin and press-in guide pin.
标签：

评论

发表评论

此博客中的热门博文

What's the properties of POM?

  Polyformaldehyde (POM) thermoplastic crystalline polymer. Known as "Super Steel" or "Sai Steel", The English abbreviation is POM. Generally, polymers obtained by formaldehyde polymerization have a low degree of polymerization and are easily thermally depolymerized. It can be used as a raw material for organic chemicals and synthetic resins, and as a fumigant for drugs. 1.General property POM  is a hard, dense material with a smooth surface and gloss, light yellow or white, thin-walled partly translucent. Combustion characteristics are easy to burn, and continue to burn after leaving the ignition source. The flame is yellow at the upper end and blue at the lower end. Melting dripping occurs and has a strong pungent formaldehyde smell and fishy smell. POM is white powder, usually opaque, good coloring, specific gravity 1.41-1.43 g/cm3, molding shrinkage 1.2-3.0%, molding temperature 170-200℃, drying conditions 80-90℃ for 2 hours. POM's long-term heat resistance ...
发表评论
阅读全文

There are several coloring methods for stainless steel parts

  There are several coloring methods for   st ainless steel parts 1. Electroplating Electroplating: The process of attaching a metal film to the surface of metal or other materials by electrolysis. It can prevent corrosion, improve wear resistance, electrical conductivity, reflectivity and enhance aesthetics.   2. Water plating It does not rely on external power supply in the aqueous solution, but only relies on the reducing agent in the plating solution to carry out the chemical reduction reaction, so that the metal ions are continuously reduced on the autocatalytic surface to form a metal plating layer.   3. Fluorocarbon paint Refers to coatings with fluororesin as the main film-forming substance, also known as fluorocarbon paint, fluorocoating, and fluororesin coating.   4. Spray paint The paint is sprayed into a mist with compressed air and applied to the stainless steel plate to form different colors.   Additional ： The current color stainless steel pl...
发表评论
阅读全文

What is 'Catch hook and thin-wall' of plastic mold products?

What is 'Catch hook and thin-wall' of  plastic mold products ?​ 1. The Catch hook The catch surface and the amount of catch hook are the important basis for the test data during assembe.  Once made any tiny mistake about these numbers, It would become a huge mistake of the product. Therefore, during mould design, We needs to pay special attentin to the catch hook assembly and testing. 2. The thin-wall What is the big problem about thin wall? The binding point is particularly easy to press and brittle, Then could't pass the test. It will be difficult to assemble in the next step, The product will be uneven filling, shrink, and easy broken.
发表评论
阅读全文